Hello everyone, I need help changing the IP address of an S7-1200 PLC from 192.168.0.1 to 10.255.255.10. I am able to download to the S7-1200, but it is not showing up in online access. Any advice would be greatly appreciated. Thank you.
Discover the precise IP address of the PLC by utilizing tools like Profinet Commander or PRONETA. Next, set up two IP addresses on your computer that are compatible with both the current PLC IP address and the desired new IP address. Make sure to avoid using an IP address that is already in use by another device on the network. Afterward, establish a connection with the PLC, transfer the project to TIA, and proceed with changing the IP address. It is crucial to note that if the PLC is a PROFINET controller and the subnet is altered, all devices in the project will need their IP addresses reconfigured.
Hey there, it seems like you've got some networking issues going on. Before you change IP addresses, make sure your PLC and PC are in the same subnet. Also, your PC's firewall or antivirus could be blocking the connection. You may need to adjust or temporarily disable them. To change the IP, you can use the TIA Portal or Siemens' IP Address Tool. If it still doesn't show up in online access, try pinging it from command prompt to confirm that your PC can see the PLC in your network.
Hi there! It sounds like you might need to modify your subnet mask to match the new IP range you're aiming for. Depending on your current network configuration, it could be causing a conflict preventing you from accessing your S7-1200 online. Additionally, ensure you're using the right programming software compatible with your PLC model. Also remember to restart your PLC after changing the IP address, sometimes a simple reset can resolve connectivity issues! Hope this helps!
Hey! It's likely that your PLC and PC are not on the same network due to mismatch in IP series. Therefore, you may need to align your PC's IP with your target IP. Considering your PLC's target IP, you could, for instance, set your PC's IP as 10.255.255.xxx (where xxx can be any value between 1 and 254, other than 10). Make sure the subnet mask is 255.255.255.0. After that, use Siemens’ ‘Set PG/PC interface’ to ensure Ethernet is selected. Then try accessing online again. Hope this helps!
Sure, I'm happy to help! Firstly, access "Devices & Networks" in the PLC within TIA Portal software. Here, you should see the currently selected network adapter's IP address. If you double click this, you will be presented with options to modify the IP address to your desired settings. Just make sure your PC's IP is in the same subnet. However, if your PLC isn't showing up in your online access, you might need to reset your PLC to factory settings to make sure no security settings are preventing access. Always remember to take a backup before making any changes.
It sounds like you might be facing a communication issue due to the IP address change. Make sure that your PC's IP address is in the same subnet as the new PLC address (like 10.255.255.x) so that they can communicate. After changing the PLC's IP address in the settings, try cycling the power on the PLC and your network equipment too, just to reset everything. Also, double-check your network configuration settings, and ensure that there are no firewall rules blocking access to the new IP. Good luck!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: 1. How can I change the IP address of an S7-1200 PLC from 192.168.0.1 to 10.255.255.10? To change the IP address of an S7-1200 PLC, you need to access the device settings through the programming software and modify the IP configuration to the desired address, in this case, 10.255.255.10.
Answer: If the S7-1200 PLC is not showing up in online access after changing the IP address, it could be due to network configuration issues. Check if the new IP address is within the same subnet as the computer trying to access the PLC, and ensure that all network settings are correctly configured.
Answer: The issue of not being able to access the S7-1200 PLC online after downloading could be related to network settings, IP address conflicts, or firewall restrictions. Ensure that the IP address is correctly configured, there are no conflicts with other devices on the network, and the necessary network permissions are in place.
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.