Has anyone successfully connected a ControLogix PLC with REA Jet Datacon software using an Ethernet connection? Any insights or advice on this integration would be highly valued.
Currently, I am involved in a rea-jet project that utilizes the ST200 interface.
I also have experience using the ST200 over RS232 to connect to a ProSoft MVI56E-GSC as a RSL5K Generic Module. While this setup may not be considered cutting-edge, it performs smoothly and effectively.
I'm completely new to this, can someone explain what the ST200 interface is? Our goal is to establish communication via Ethernet.
The ST200 provides a reliable Serial ASCII communication link for REA DOD type systems controllers, offering RS232, RS422, or RS232/422 connectivity options. While the initial setup may be a bit cumbersome and the User Manuals appear to be translations from German, the system proves to be efficient and dependable once in operation.
Hey everyone! I'm in need of programming references for the REA ST200 printer terminal to connect it with Logix using the Anybus serial gateway. Unfortunately, I have been unable to find any documentation for the printer terminal online (only available in Russian). Any assistance would be greatly appreciated. Thanks!
Yes, I have been successful in connecting a ControlLogix PLC with REA Jet Datacon software using an Ethernet/IP connection. A crucial point is consistent data mapping on both devices. I suggest using the Generic Ethernet Module object in the RSLogix/Studio 5000 and configuring it appropriately. Also, I had to ensure that both devices were on the same subnet. If it's well set up, you should be able to read/write data between the PLC and the Datacon software seamlessly. Good luck with your integration!
Yes, I've done this integration. The key is to ensure your ControlLogix PLC is running firmware that's compatible with the REA Jet Datacon software. Also, remember that the IP address on both devices needs to be in the same subnet. Lastly, you might have to adjust the firewall settings on the side of the Datacon software to allow incoming connections. The process isn't extensively documented by REA Jet, but with a little patience and troubleshooting, it's definitely possible.
I've had some experience with this type of integration. The most important thing to ensure is that your ControLogix PLC has the latest firmware installed and that it's correctly configured for network communication. You might need to set a static IP for this. Within the REA Jet Datacon software, check the settings to make sure they match the PLC’s. It took me a few trials to get the communication right. Also, always remember the crucial step to set your PLC into 'RUN' mode and not in 'PROG' mode when trying to connect. Good luck with your setup!
Absolutely! I successfully connected a ControlLogix PLC with REA Jet Datacon software using an Ethernet connection. The key here is to ensure all your drivers are up-to-date, especially emphasizing on the RSLinx Classic which facilitates the communication between the two. Additionally, ensure your firewall settings are set correctly and are not obstructing the connection. Hope this helps!
I've worked on integrating ControLogix PLCs with REA Jet Datacon software over Ethernet, and I can share that using the right communication protocols is crucial. Make sure to verify your IP settings and ensure that the PLC is configured for UDP or TCP connections, depending on your setup. It can be helpful to use the built-in diagnostic tools in both systems to troubleshoot any connectivity issues. Also, consider checking the firmware versions to ensure compatibility. Good luck with your project!
I've successfully integrated a ControLogix PLC with REA Jet Datacon software over Ethernet, and I found that using the correct Ethernet settings was crucial for a smooth connection. Make sure the IP addresses are properly configured for both devices, and don't forget to check the firewall settings on your network. I also found that using explicit messaging for data exchange helped streamline the process. If you're facing issues, it might be worth looking into the protocol compatibility as well. Good luck!
I've successfully connected a ControLogix PLC to REA Jet Datacon over Ethernet, and I found that ensuring proper IP addressing and subnet configurations were crucial for smooth communication. Be sure to use the right driver configuration in Datacon and double-check your PLC's communication settings. Also, consider using the "Logix Message" instruction for sending data—this helped me streamline the integration process. Good luck, and feel free to reach out if you have any specific questions about the setup!
I haven’t personally set it up, but I’ve heard from others that establishing an Ethernet connection between ControLogix PLCs and REA Jet Datacon can be quite smooth if you ensure that both devices are on the same subnet. It’s crucial to configure the PLC’s Ethernet port correctly and use the right protocols, like TCP/IP. Additionally, make sure to utilize any available libraries or drivers in Datacon that facilitate communication with Allen-Bradley systems; it can save a lot of time troubleshooting. Don’t forget to check the compatibility of firmware versions too—sometimes that can make a big difference!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: Answer: To connect a ControLogix PLC with REA Jet Datacon software using Ethernet, you will need to configure the communication settings on both devices and ensure they are on the same network.
Answer: Answer: Ensure that the IP addresses of the PLC and the software are properly configured, check for any firewall or network settings that might block communication, and follow the manufacturer's guidelines for establishing the connection.
Answer: Answer: Make sure that the ControLogix PLC and REA Jet Datacon software support Ethernet communication protocols and that they are compatible with each other. It's also important to verify that the network infrastructure can support the communication requirements.
Answer: Answer: Check the physical connections, verify the IP settings, inspect network configurations, and ensure that both devices are powered on and functioning correctly. Additionally, reviewing error logs or contacting technical support for both devices can help in resolving any connectivity issues
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.