Hello everyone, I am looking to connect online with a Modicon PLC using Concept 2.6. While I have experience with Allen Bradley PLC's, I have discovered that Modicon does not use individual programming files like Rockwell. Therefore, I transferred my entire project folder to C:/concept and accessed the project from there. Now, I need assistance in configuring IPs for the connection. Any additional advice or techniques for working with Modicon and Concept 2.6 would be greatly helpful and appreciated. Explore more about connecting Modicon PLC online, configuring IPs, and tips for using Concept 2.6.
Are you attempting to achieve high performance by connecting a Momentum CPU via Ethernet?
In the case that the CPU belongs to the Momentum family, it is important to note that the program was not stored as an individual file in the past. Derived Function Blocks (DFBs) and User-Defined data types were generated in a separate environment from the main programming. The 'source code' was typically not transferred to the PLC due to memory constraints, preventing users from uploading it. If the program files were lost on the hard drive, it would not be possible to connect to or monitor the PLC. Ensuring that you can successfully perform an Ethernet ping of the CPU's IP address is the initial step to take. The project documentation should provide guidance on determining the specific IP address.
Hey there, jkhan! Can you provide a photo of the modicon device you're attempting to connect to the internet with? Is there an ethernet card installed on it? Are you currently linked to that ethernet card? Have you tried pinging the device? Let me know!
It's been a while since I last worked in a concept shop, but I remember that having an 'equal' version of the program was crucial. There were two program formats - a compiled and uncompiled one. Thankfully, there was a conversion utility to switch between them. Are your programs in .asc format? Make sure to expand them first. Once expanded, you should see .prj files along with various subdirectories and additional files.
Hey there, the first thing to note when connecting to a Modicon PLC is that unlike Allen Bradley PLC's which often use Ethernet/IP, Modicon generally uses Modbus TCP/IP for communication. Hence, your network settings should be compatible with this protocol. Regarding the IP configuration, it is usually done in the PLC configuration software (Concept 2.6 in your case). Go to PLC->Network Support-> NOE Modules, then specify your IP, subnet, and gateway. Ensure this aligns with your network rules. One tip I always find useful when using Concept 2.6 is to keep my documentation as clear as possible. Since Concept doesn't separate its programs like Rockwell, your comments and documentation should be inclusive to avoid confusion. Good luck in your project, communication with Modicon might be a bit different than you're used to, but with a little bit of practice, it can be quite intuitive.
Sure thing, with Modicon, one key step in connecting is to ensure you've assigned an IP address to your PLC through the Unity Pro software. Go to 'online' tab, click on 'Set address' and input the correct IP. If you're on a network, be sure to speak to your IT department for an appropriate IP, subnet mask, and gateway. Also, remember to always execute a 'Build All' in Concept before downloading your project to the PLC. As for tips, practice makes perfect so spend time familiarizing yourself with the Concept software, as it runs differently to Rockwell. Special features like Derived FBs can be quite useful. Good luck!
Hey! Connecting to Modicon PLCs can definitely feel a bit different coming from Allen Bradley. For your IP configuration, make sure your PC's IP address is in the same range as the PLC’s. You can usually access the PLC’s configuration through its built-in web interface to set or check the IP. Also, don't forget to enable communication settings in Concept 2.6. A tip I found helpful is to keep your project organized with clear naming conventions since Modicon doesn't separate files like Rockwell; it saves a lot of time navigating through complex projects. Good luck, and let me know if you hit any snags!
It sounds like you’re on the right track with the project folder setup! For connecting to your Modicon PLC with Concept 2.6, make sure you’re using the correct IP configuration by checking both your PC’s network settings and the PLC’s IP address—make sure they’re on the same subnet. A great tip is to use the ‘Communication’ menu in Concept to configure the Ethernet port; just make sure the settings match what you have set in your PLC. Also, don’t forget to check any firewalls or antivirus settings that might block the connection. Good luck, and feel free to reach out if you hit any snags!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: - To connect online with a Modicon PLC using Concept 2.6, you can transfer your project folder to a specific location, such as C:/concept, and access the project from there.
Answer: - To configure IPs for the connection with a Modicon PLC, you may need to set up the appropriate network settings within Concept 2.6. This typically involves specifying the IP address of the PLC and ensuring the network configuration aligns with your setup.
Answer: - Yes, there are differences in how programming files are handled between Modicon PLCs and Rockwell PLCs. Modicon PLCs do not use individual programming files like Rockwell, so it's important to adapt your workflow accordingly when working with Modicon PLCs in Concept 2.6.
Answer: - Additional advice for working with Modicon PLCs and Concept 2.6 includes familiarizing yourself with the specific features and functionalities of Concept 2.6, understanding Modicon's programming structure, and ensuring proper configuration of IPs for online connectivity. Regularly referring to the user manual and seeking assistance from forums or experts can also be beneficial.
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.