Hello, I am seeking information on the compatibility of the LS PLC controller model XBM-DN32S with the Mitsubishi PLC controller model FX5U-64M. I need to establish communication between the two controllers in order to send a signal from the Mitsubishi PLC to stop the conveyor controlled by the LS PLC. Thank you.
Although I have not personally used LSIS PLC, after reviewing various datasheets, I discovered there are multiple communication options available. Modbus and EtherNet I/P are two popular choices, with Modbus particularly advantageous as it does not require any additional purchases on the Mitsubishi side. This flexibility in communication protocols can allow for seamless integration and increased efficiency in industrial automation systems.
In my opinion, I have not personally used LSIS PLC, but based on a quick review of the datasheets, it seems that there are multiple communication options available. Both Modbus and EtherNet I/P are supported, with the added benefit of not requiring any additional purchases on the Mitsubishi side when using Modbus. However, I am still unclear on how the wiring needs to be configured for communication using Modbus. Can anyone provide further insight on this matter?
If you're looking for a simple and effective way to connect devices, consider using a communication cable like Ethernet or 485. Instead of using multiple signals, you can simply connect the output of one device to the input of another, creating a volt-free contact for efficient communication. This method is straightforward yet highly effective for establishing a connection between devices.
Parky suggested that for simple wiring, a communication cable such as Ethernet or 485 could suffice. If only one signal is needed, it may be more efficient to connect an output from one PLC to an input on the other, using the output as a volt-free contact and supplying voltage from the other PLC. I agree with this approach, especially if the PLCs are located on the same panel. If they are close enough and only a digital signal is required, using DI/DO is a simpler option than an industrial protocol. Additionally, if there are two signals, implementing a simple heartbeat program could help monitor the status of the other PLC.
From my experience, it's indeed possible to establish communication between LS XBM-DN32S and Mitsubishi FX5U-64M PLCs. The common approach is to use a Modbus communication protocol. However, you would require a dedicated RS485 Serial communication module for Mitsubishi FX5U. Keep in mind that you'll need to understand how to set up communication parameters and write PLC code for both systems in order to properly interpret conveyed signals. It could be intricate, so you might want to consider seeking out assistance from an automation engineer if you're not familiar with this.
Both LS PLC and Mitsubishi PLC are popular brands and can usually establish communication with each other via Modbus communication protocol. However, establishing direct communication between different models (like XBM-DN32S and FX5U-64M) might not be that straightforward due to possible variations in their communication settings. It will be beneficial to check both their manuals or technical specs to see if they support the same communication protocols, baud rates, data bits, etc. If not, you may need a protocol converter. Involve an automation engineer for the best result. Also, remember to ensure proper isolation, to protect both systems from possible faults.
Hey there! Establishing communication between the LS PLC XBM-DN32S and the Mitsubishi FX5U-64M can be a bit tricky, but it’s definitely doable. You’ll likely want to look into using a common protocol like Modbus TCP or possibly making use of their respective serial communication features. Just make sure to check the specific settings for communication parameters like baud rate and data format on both sides. If they can talk via a shared protocol, you should be able to send that stop signal to control your conveyor without too much hassle. Good luck!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: 1. Are the LS PLC XBM-DN32S and Mitsubishi PLC FX5U-64M compatible for controller communication? - Yes, the LS PLC XBM-DN32S and Mitsubishi PLC FX5U-64M are compatible for controller communication.
Answer: - The purpose is to send a signal from the Mitsubishi PLC to stop the conveyor controlled by the LS PLC.
Answer: - You can set up communication between the two controllers by configuring the appropriate communication protocol and settings in both PLCs.
Answer: - It is important to ensure that the communication protocols and settings are correctly configured in both the LS PLC XBM-DN32S and Mitsubishi PLC FX5U-64M to establish successful communication.
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.