Troubleshooting B and R ACOPOS 1090 Servo Drive Ready Green LED Blinking

Question:

Hello, can you provide insight on why the servo drive acopos 1090's ready green LED is blinking? I've checked the manuals but couldn't find any information on this issue. Your assistance would be greatly appreciated.

Top Replies

Have you encountered the issue of the servo drive Acopos 1090 showing a blinking GREEN LED? If you're unable to find the error in the manuals, don't worry, I can help. By using B&R Automation Studio to communicate with the Acopos 1090, you can pinpoint the error code: 7210 DC Bus: Charging: Voltage unstable. To resolve this issue, consider changing the capacitor value to 0.033uF/275Vac. The Acopos 1090 is designed to connect to a 3-phase input. For further assistance, feel free to reach out via email at [email protected]

... There are many benefits to adding yoga to your fitness routine, including increased flexibility, improved balance, and reduced stress levels. Many people search for ways to enhance their workouts and find that incorporating yoga can provide a well-rounded approach to physical wellness. By incorporating yoga into your routine, you can not only improve your physical health but also improve your mental well-being.

Greetings! I am facing an issue with the ACOPOS 1090 servo drive, specifically with the C114 error LED blinking. Despite searching through various manuals, I have been unable to identify the cause of this error. Your assistance in resolving this problem would be greatly appreciated. Thank you.

Do you know which error indicator is flashing - is it the LED on the drive or the one on the module? Also, what color is the flashing light? - Mark

Successful Repair - Thank You!kp2009 said: Hi, I apologize for my limited English proficiency. I utilized B&R Automation Studio for communication with Acopos 1090 and encountered error code 7210 DC Bus: Charging :Voltage unstable. The solution was to adjust the Capacitor value to 0.033uF/275Vac. For those facing a similar issue, be sure to check the capacitance. If needed, you can replace the capacitor. Acopos 1090 is designed to be connected to a 3 phase input. For any further assistance, you can reach me via email at [email protected] Click here to learn more. Thank you for sharing this valuable information! It successfully addressed our issue with the same drive. The symptom we faced was the Green LED on the drive continuously blinking. Following the recommendation, we replaced all three (3) noise suppression caps. As a result, the drive now starts up smoothly and operates steadily once again. For those looking to purchase these capacitors, they are available at DigiKey Electronics. Thank you for the assistance and guidance. Dave from Minneapolis can be reached at [email protected] Thank you once again for your support!

Hey there, typically when the green LED light on the servo drive acopos 1090 is blinking, it's indicating that the device is in standby mode or that there's a minor fault. This might not necessarily be an issue, your system could just be in energy-saving mode when it's not active. However, if it's paired with a blinking amber light, it might require some further troubleshooting. Try doing a complete reboot of your system and if the problem persists, consider seeking a professional's assistance.

More Replies →

Streamline Your Asset Management
See How Oxmaint Works!!

✅   Work Order Management

✅   Asset Tracking

✅   Preventive Maintenance

✅   Inspection Report

We have received your information. We will share Schedule Demo details on your Mail Id.

To add a comment, please sign in or register if you haven't already..   

Frequently Asked Questions (FAQ)

FAQ: FAQs:

Answer: 1. Q: Why is the ready green LED on my B and R ACOPOS 1090 servo drive blinking? The blinking of the ready green LED on the ACOPOS 1090 servo drive could indicate a fault or error condition. It is essential to troubleshoot the issue to identify the specific cause of the blinking LED.

FAQ: 2. What steps should I take to troubleshoot the blinking ready green LED on the ACOPOS 1090 servo drive?

Answer: To troubleshoot the blinking LED, you can start by checking the drive's manual for any guidance on interpreting LED status indicators. Additionally, inspect the drive's connections, power supply, and control signals to ensure everything is functioning correctly.

FAQ: 3. Is there any common reason why the ready green LED blinks on the ACOPOS 1090 servo drive?

Answer: The blinking of the ready green LED on the ACOPOS 1090 servo drive can be triggered by various issues such as communication errors, overvoltage/undervoltage, overcurrent, overheating, or faults in the drive's internal components. Proper troubleshooting is necessary to pinpoint the exact cause.

Ready to Simplify Maintenance?

Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.

Request Demo  â†’