Hello everyone! I encountered issues while trying to install a new FC302 frequency drive to replace a Danfoss VLT5011. The problem lies in the Devicenet network not recognizing the new drive. Despite using the Devicenet Manager software, which is unfamiliar to me and lacking a user manual, my attempts to resolve this have been unsuccessful. I followed the steps of installing the corresponding EDS file for the FC302, setting up the connection, removing the old device from node 40, and adding the new device from the EDS list. However, the network still does not recognize the new device, without even displaying a question mark like RSNetworx does. Additionally, I have not discovered any icons or commands for downloading or uploading network configurations to or from the scanner. I seek guidance on modifying the network configuration and downloading it to the scanner using Devicenet Manager. Any assistance on ensuring the correct procedure for replacing the device in node 40 would be greatly appreciated. Thank you in advance. Regards, Juan
Are you currently utilizing DeviceNet Manager or RSLinx in your network management system?
Have you assigned a DeviceNet address to the FC302?
Hello, could you kindly provide me with information on how to obtain EDS files for fc 302? Thank you. Regards, Nauman. Contact me at [email protected] for assistance.
Hi Juan, it sounds like you've already taken some critical steps. Sometimes Devicenet can be finicky with hardware recognitions. Check if your EDS file for the FC302 is the most recent version and compatible with your Devicenet Manager software. Additionally, give it a try by resetting the Devicenet network. Unplug all the devices, power it back up, and then add them back one-by-one beginning with the FC302. As for uploading and downloading network configurations, there should be an option located somewhere in the tools or options menu of the software. But it depends on the version of Devicenet you're using. I would recommend reaching out to the tech support of the software you're using. They can provide you with a detailed guide and if there is some compatibility issue they are the best ones to solve it.
Hi Juan, it can be certainly hard to adapt when diving into unfamiliar software and hardware. As you've mentioned that you've plugged in the EDS file for your FC302, I would suggest double-checking the accuracy of this file first, as it could be a possible pain point. Also, it's possible that there might be compatibility issues with the Devicenet software and the new drive, hence it's unable to detect it. Try updating your Devicenet software if possible. As for downloading or uploading network configurations to/from the scanner, frequently there are specific commands or sequences which are not straightforwardly available on the user interface. Reach out to Danfoss' technical support if you haven't already, providing them with a detailed overview of the steps you've already taken. They may have further knowledge or software specific to this transitioning process.
Hey Juan, it seems like you've already tried quite a bit. But when you removed node 40, did you rescan the network in DeviceNet Manager? Sometimes, just refreshing the network view can solve problems with unrecognized devices. Additionally, it's important to ensure the EDS file you have for the FC302 is correctly installed. You might have to install it again if there was any interruption during the initial installation. Make sure you're running the latest version of DeviceNet Manager as well. Older versions may not properly recognize newer devices. Lastly, double-check that the FC302 parameters match the EDS parameters, as discrepancies could also cause recognition issues. Hope this helps you solve your problem. Best of luck!
Hi Juan, sorry to hear you're having issues. I've dabbled with Devicenet Manager before and it can be a bit daunting. Regarding your issue, you could try two things. First, make sure your EDS file is installed correctly, if there's a mismatch, the network might not recognize your new drive. Try re-installing the EDS file just to be sure. Second, it might be a problem with the Devicenet Manager configuration. Make sure that when you remove the old device from node 40, the node address doesn't get stuck to the retired device. To do this, you could try resetting the network, clean up any residual issues and then add the new device to node 40. As for downloading or uploading network configurations, I think Devicenet Manager should automatically prompt you to do either once the new device has been successfully added. Hope this helps, please do let us know if anything works out.
Hi Juan! It sounds like you're dealing with a frustrating situation. Have you double-checked that the EDS file for the FC302 is correctly installed and linked? Sometimes the issue can arise from configuration mismatches, so verifying that all settings (like node addressing and baud rate) match your network requirements is crucial. Also, try restarting the Devicenet scanner after making changes, as it may help refresh the network. If you're still having trouble, consider reaching out to the manufacturer's support team—they often have valuable insights for specific integration issues. Good luck, and keep us posted!
Hey Juan! It sounds like you’ve been through quite the troubleshooting process. One thing I’d suggest is double-checking the EDS file’s version to ensure it matches the specific firmware on your FC302, as sometimes mismatches can cause recognition issues. Also, in the Devicenet Manager, confirm that the proper communication settings (like baud rate and node address) are configured correctly and that there are no conflicting addresses on the network. If you're still stuck, it might help to reboot both the scanner and the FC302 after making changes to see if that resets the communication. Good luck, and hopefully, you'll get it sorted soon!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: Answer: Troubleshooting Devicenet installation issues for a Danfoss FC302 Frequency Drive involves steps like installing the EDS file, setting up the connection, removing the old device, and adding the new device. It also requires using the Devicenet Manager software correctly.
Answer: Answer: To resolve the issue of the Devicenet network not recognizing a new drive, ensure that the correct EDS file for the FC302 is installed, follow the proper steps for setting up the connection, and make sure the new device is added from the EDS list.
Answer: Answer: To modify the network configuration and download it to the scanner using Devicenet Manager, refer to the software's functionalities and commands for downloading or uploading network configurations. It may also be helpful to seek guidance or a user manual for using Devicenet Manager effectively.
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.