Good morning! I am currently working on a project in TIA Portal and I am facing an issue with uploading it from the PLC. In the project tree, I have noticed an orange exclamation mark on the PLC tags folder. However, upon expanding the folder, I am unable to identify the specific differences. When conducting an online/offline comparison, it indicates that the entire PLC Tags folder is missing from the online project. Any insights or suggestions on resolving this issue would be highly valued.
It's unclear what could be causing the issue, but it's likely minor as all program blocks are showing up as green. If certain tags were impacting the program blocks, they would be highlighted in orange. Ultimately, it's important to verify if the offline project aligns with the online PLC, and it appears that it does. This comparison helps ensure that the program is functioning correctly and efficiently.
What version of TIA Portal is recommended? I encountered a similar issue in TIA 13 where blocks displayed a green equal state, but there were problems with PLC tags. The root of the problem was that the PLC upload did not capture all symbol name addresses, and the offline project contained %MW tags. When inspecting the blocks, I noticed unknown addresses with ??? marks. I have not experienced the same issue in TIA 15 and newer versions.
Lare inquired about the TIA Portal version causing issues with PLC tags displaying errors despite blocks showing a green equal state. The problem stemmed from incomplete symbol name addresses during PLC upload, resulting in %MW tags in the offline project. Notably, there were unknown addresses marked with "???" on the affected blocks in TIA 13, but such issues have not recurred in TIA 15 versions. As for my TIA 14 setup, I encounter discrepancies between online and offline projects even after uploading and obtaining a green circle for all FBs. When attempting to download changes to the PLC, I am prompted about inconsistencies between projects. I have shared a photo illustrating these challenges for better clarity.
Hi! It sounds like an upload error occurred due to mismatched tags between your online and offline projects. One way to resolve this could be to ensure that all the tags in your offline project are correctly defined and correspond with those in your online project. Additionally, check if any PLC tags got accidentally deleted or renamed. Sometimes, this can also occur if there's a versioning mismatch between your PLC and TIA Portal. Try updating TIA Portal or reinstalling the PLC drivers to ensure compatibility.
Hi there! It seems like there could be a synchronization issue between your offline and online versions of the project. I would suggest first trying to recompile your project in TIA Portal, to see if that resolves the discrepancy. If that doesn't work, you might have to manually export the PLC tags from your offline project and then import them into your online project. Be sure to back up your work before making these adjustments. It's also worth checking whether there are any PLC tag properties that might be causing this issue, like unsupported tag types or names. Hope this helps and you manage to find a solution soon!
Hello! It sounds like you're having an issue that might be related to the file synchronization between TIA Portal and the PLC. The orange exclamation symbol usually indicates there are differences between the offline and online versions of your project. If it states the entire PLC Tags folder is missing online, it might be due to a failed or incomplete upload. My suggestion would be to try uploading the project again. Make sure the PLC is properly connected and you're using a reliable network. Before that, you may also want to check for any error messages in the diagnostics buffer which may provide more insights into what's going wrong.
Good morning! It sounds like you're dealing with a frustrating issue. The orange exclamation mark typically indicates that there are discrepancies or missing elements in your online project. Have you tried refreshing the PLC connection or rebooting the PLC? Sometimes, this can clear temporary glitches. Also, check if there are any firmware updates available for your PLC, as older firmware can sometimes lead to synchronization problems. Lastly, you might want to export your current project and then re-upload it to see if that resolves the discrepancy. Good luck!
Good morning! It sounds like you're dealing with a tricky situation. The orange exclamation mark usually indicates some sort of discrepancy, but the missing PLC Tags folder in the online comparison is definitely a red flag. Have you tried checking the 'Project View' under the online connections to ensure you're correctly connected to the right PLC? Sometimes, re-establishing the connection or reloading the project can help clear up inconsistencies. Also, make sure that you're using the same version of TIA Portal that was used for the original programming—it can lead to issues if versions don't match. If all else fails, consider exporting your tags data from the offline project and importing it into the online version as a workaround. Good luck!
Good morning! It sounds like you're dealing with a tricky situation in TIA Portal. The orange exclamation mark usually points to some sort of mismatch or missing components. Have you tried checking if the PLC tags are actually loaded in the PLC? Sometimes, a simple refresh or a re-upload of the project can resolve discrepancies. Also, double-check that your project settings and PLC configurations are aligned—any version mismatches could cause tags to show as missing. If all else fails, consider exporting the tags from your offline project and manually importing them to the online project to see if that resolves the issue. Good luck!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: Answer: The orange exclamation mark typically signifies that there are inconsistencies or issues within the PLC tags folder, such as missing or mismatched tags.
Answer: Answer: You can expand the PLC tags folder to compare the online and offline versions, or conduct an online/offline comparison to pinpoint any missing or mismatched tags.
Answer: Answer: This issue could be due to synchronization problems between the offline project and the PLC, resulting in the PLC Tags folder not being updated or transferred correctly.
Answer: Answer: You can try re-uploading the project from the PLC, checking for any synchronization errors, ensuring proper project settings, and verifying tag consistency between the offline and online versions.
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.