Hello! I am new to this area and in need of assistance with a problem I am facing. I have inherited projects for plants created in Unity Pro XL, which utilize the SVI1000 HART DTM in an outdated version (1.0.100.0). Despite installing the version from the original site, I am still encountering compatibility issues. Can anyone suggest where I might be able to find the correct version? The error message I am receiving warns of a potential issue with DTM compatibility, specifically with the SVi1000 HART DTM, due to a version mismatch (1.00.100.0). The error suggests that the DTM may not be installed on the PC or may be installed without version information.
Where can I find vintage Masoneilan DTMs for purchase?
It appears that the DTM library you need can be found on the Baker Hughes website's Resource Center. Specifically, you can access it here: https://dam.bakerhughes.com/m/56500...oneilan-SVi1000-DTM-Installation-Software.exe If you filter the results by selecting Software, you will find the DTM Installation software mentioned above, along with the option to download the Masoneilan ValVue Installation Software. It is possible that the DTM library is included in this software as well. If you intend to make configuration changes using this tool, having it on hand would be beneficial. Alternatively, you could consider using PactWARE or Unity Pro XL (Ecostruxure Control Expert now), but be cautious as they may require a full download if changes are made. Ultimately, the choice is yours.
I have attempted to install version V2.10.1 of the drivers as well as ValVue3, but unfortunately, I have not seen any positive results. The project is developed in UnityProXL, and consistently displays a warning indicating that SVI1000 204-1.1.1 cannot be located within the same family. Despite installing all available DTM from the relevant site, resembling SVI, the issue persists. This potential problem may be attributed to compatibility issues with the DTM version: SVi1000 HART DTM. An error is encountered when checking DTM compatibility (DTM version in the application is 1.00.100.0). It is possible that the DTM on the PC is either not installed or installed without proper version information. Thank you for your assistance.
Hi there! Sounds like you're facing a bit of a pickle with the SVi1000 HART DTM. Firstly, I'd suggest double-checking your installation steps, since a common cause of this error can be a minor misstep during this process. Remember, the DTM and Unity Pro XL should ideally be installed in a specific order for optimum compatibility. Secondly, though your system may indeed be pointing out a version mismatch, it could also be an issue of the DTM not being registered correctly. You can verify this by using a DTM Browser to check registration. Lastly, if you're still stuck, the Schneider Electric forum might have some useful threads related to this issue too. Hope that helps!
Hey there! Ah, the frustrating joy of inheriting project work! It seems you've hit one of those notorious DTM compatibility roadblocks. One thing to clarify though, are you certain that the problem arises from the version mismatch? If you've already tried installing the version from the original site, there might be underlying issues. However, if you're sure it's the version mismatch, a possible solution could be to check back on the original project documentation or with the previous project manager for the exact version used. Additionally, some online forums and platforms like GitHub host older versions of these DTMs that aren't available on official sites. Lastly, ensure that your Unity Pro XL software is updated and fully compatible with the DTM in use. Hope this helps, and do share your progress!
Hey there! It sounds like you're in a bit of a bind with the DTM version mismatch. Have you tried reaching out to the original vendor or checking their support forums? Sometimes, older software versions can be tricky to find, but they might have archived versions or be able to provide you with a direct link. Also, it’s worth checking if there are system requirements or updates for Unity Pro that you might have missed, as that can sometimes resolve compatibility issues. Good luck!
Hey there! It sounds like a frustrating situation with the DTM compatibility. Have you checked if there's an updated version of Unity Pro XL itself that might better support the DTM you need? Sometimes, older versions can have quirks like that. Additionally, you might want to reach out to Schneider Electric’s support or community forums; they can often provide access to legacy software versions or patches that aren’t publicly listed. Good luck!
✅ Work Order Management
✅ Asset Tracking
✅ Preventive Maintenance
✅ Inspection Report
We have received your information. We will share Schedule Demo details on your Mail Id.
Answer: - You may need to search for the correct version of the SVI1000 HART DTM on the official website of the manufacturer or reach out to their customer support for assistance.
Answer: - To resolve compatibility issues, ensure that you have the correct version of the DTM installed on your PC. You may need to uninstall the current version and then install the correct version as per the requirements of your Unity Pro XL projects.
Answer: - If you encounter an error message regarding a version mismatch, try reinstalling the SVI1000 HART DTM with the correct version. Make sure to follow the installation instructions carefully to ensure proper compatibility.
Answer: - The compatibility issues could arise due to incorrect installation of the DTM, using an outdated version, or missing version information during installation. Ensure that you have the correct and up-to-date version of the DTM installed on your system.
Join hundreds of satisfied customers who have transformed their maintenance processes.
Sign up today and start optimizing your workflow.